Render Repair
Bead and Corner Repair
Replacing rusted or damaged corner beads, stop beads and bellcasts that cause staining, cracking and render loss.

What's involved
Beads are the metal or PVC profiles that form crisp corners, edges and the drip line above the damp proof course. On older render, galvanised steel beads rust, expand and push off the render around them, leaving orange streaks and cracked arrises. The renderer cuts out the render along the damaged bead, removes the old profile and fits a new stainless steel or PVC bead, bedded and set to line. The render is then rebuilt and finished to match. Bellcast beads above the damp proof course are especially important, because if render runs down to the ground it can draw moisture up into the wall and bridge the damp course. Replacing a corner bead on a two-storey wall usually takes a day with scaffold or a tower, plus decoration once the repair has cured.
How we handle it
Send photos of the damage
Use the quote form to show us cracks, bulges, missing patches or stains, and tell us roughly how large the affected area is and how high up it sits. Mention any damp appearing on inside walls nearby.
On-site inspection
A local renderer taps the walls to map hollow areas, checks gutters, sills, beads and the damp proof course, and identifies what caused the failure. They explain whether repair or re-render gives better value.
Clear, itemised quote
You receive a written quote listing each repair area, the cause to be fixed, access needed such as towers or scaffold, the finish to be matched and any decoration required to blend the repair in.
Cut back and rebuild
Damaged render is cut back to sound edges, the wall is prepared, beads are replaced where needed and new render coats are applied to the same thickness and texture as the surrounding finish.
Blend and tidy up
Once cured, repairs are painted or recoated to blend in, the area is cleaned and waste is removed. You get photos of the finished repair and advice on any areas worth watching.
Price guide
Render repair is priced by the size and number of repair areas, how hard they are to reach, and how much work is needed to match the finish. Small, low-level repairs are often quoted as a fixed job, while larger areas are priced per square metre. These are typical UK guide prices for 2026, excluding structural repairs to the wall itself.
- Render survey with written report: £150–£350. Tapping survey, photos and recommendations; often credited if you go ahead with the repairs.
- Render clean and algae treatment: £400–£1,200. Biocide treatment and soft wash for a typical house, depending on elevations and access.
- Corner bead replacement: £200–£450 per corner. Single-storey corner; two-storey corners need a tower or scaffold, which is priced separately.
Questions about bead and corner repair
How much does render repair cost in the UK?
Small render crack repairs start from around £150, while patch repairs of blown render typically cost £60 to £120 per square metre in the UK in 2026. Pebbledash patches cost a little more because the aggregate is thrown by hand. Scaffolding or towers for upper floors and painting to blend the repair are often the biggest extra costs.
Can render repairs be matched to the existing finish?
Render repairs can be closely matched, but an exact invisible match is difficult because weathering changes colour and texture over time. For painted render, repainting the whole elevation after repair gives a uniform finish. For silicone render, recoating a complete panel between corners or beads hides repairs best. Pebbledash aggregate can rarely be matched perfectly.
Can render be repaired in winter?
Small render repairs can sometimes be done in winter on mild, dry days, but most render products should not be applied below about 5°C or when frost is forecast. Cold slows curing and frost can damage fresh render. Temporary repairs to stop water getting in can be made in winter, with full repairs scheduled for spring.
Other services
Crack Repair
Raking out, filling and reinforcing cracks in render, from fine crazing to structural cracks needing investigation first.
Blown and Hollow Render Repair
Finding render that has lost its bond with the wall, cutting it back to sound edges and rebuilding the coats.
Pebbledash and Roughcast Repair
Patching failed pebbledash or roughcast with matching aggregate, or advising when full removal is the better option.
Silicone and Monocouche Render Repair
Repairing impact damage, cracks and staining on modern thin-coat and through-coloured render systems.
Render Survey and Damp Investigation
Tapping, inspection and moisture checks to map failing render and find the cause before any repair starts.
Bead and Corner Repair near you
Get a free render repair quote
Tell us what you need and we'll come back with a clear price.
Request a quote