Render Repair
Crack Repair
Raking out, filling and reinforcing cracks in render, from fine crazing to structural cracks needing investigation first.

What's involved
Not all render cracks are equal. Fine crazing across the surface is usually shrinkage from the original application and is mainly cosmetic. Cracks running from window and door corners, along lintels or in straight lines often point to movement, corroded steel or missing beads. Wider cracks, especially stepped cracks or those over 5mm, can signal subsidence, failed wall ties or lintel problems and should be checked by a surveyor before any patching. For non-structural cracks, the renderer opens the crack into a V with a grinder or chisel, removes loose material, applies a bonding primer and fills with a flexible repair mortar. Longer cracks are bridged with a strip of alkali-resistant mesh in a basecoat so they do not reappear. A handful of cracks on one elevation is typically half a day to a day, plus painting to blend.
How we handle it
Send photos of the damage
Use the quote form to show us cracks, bulges, missing patches or stains, and tell us roughly how large the affected area is and how high up it sits. Mention any damp appearing on inside walls nearby.
On-site inspection
A local renderer taps the walls to map hollow areas, checks gutters, sills, beads and the damp proof course, and identifies what caused the failure. They explain whether repair or re-render gives better value.
Clear, itemised quote
You receive a written quote listing each repair area, the cause to be fixed, access needed such as towers or scaffold, the finish to be matched and any decoration required to blend the repair in.
Cut back and rebuild
Damaged render is cut back to sound edges, the wall is prepared, beads are replaced where needed and new render coats are applied to the same thickness and texture as the surrounding finish.
Blend and tidy up
Once cured, repairs are painted or recoated to blend in, the area is cleaned and waste is removed. You get photos of the finished repair and advice on any areas worth watching.
Price guide
Render repair is priced by the size and number of repair areas, how hard they are to reach, and how much work is needed to match the finish. Small, low-level repairs are often quoted as a fixed job, while larger areas are priced per square metre. These are typical UK guide prices for 2026, excluding structural repairs to the wall itself.
- Render survey with written report: £150–£350. Tapping survey, photos and recommendations; often credited if you go ahead with the repairs.
- Render clean and algae treatment: £400–£1,200. Biocide treatment and soft wash for a typical house, depending on elevations and access.
- Corner bead replacement: £200–£450 per corner. Single-storey corner; two-storey corners need a tower or scaffold, which is priced separately.
Questions about crack repair
How much does render repair cost in the UK?
Small render crack repairs start from around £150, while patch repairs of blown render typically cost £60 to £120 per square metre in the UK in 2026. Pebbledash patches cost a little more because the aggregate is thrown by hand. Scaffolding or towers for upper floors and painting to blend the repair are often the biggest extra costs.
Is cracked render a serious problem?
Cracked render can become serious because it lets water get behind the render and into the wall. Fine surface crazing is usually cosmetic, but cracks from window corners, horizontal cracks and anything wider than about 5mm should be checked. Water trapped behind render can cause blown patches, internal damp and frost damage, so repairing cracks early is cheaper.
Why does render crack?
Render cracks for several reasons: shrinkage while drying, a mix that was too strong, missing movement joints, rusting steel beads, building movement or water freezing behind the surface. Cracks at window corners often come from stress concentrations or lintel movement. Identifying the cause matters, because simply filling a crack without fixing the reason usually means it returns.
Other services
Blown and Hollow Render Repair
Finding render that has lost its bond with the wall, cutting it back to sound edges and rebuilding the coats.
Pebbledash and Roughcast Repair
Patching failed pebbledash or roughcast with matching aggregate, or advising when full removal is the better option.
Silicone and Monocouche Render Repair
Repairing impact damage, cracks and staining on modern thin-coat and through-coloured render systems.
Bead and Corner Repair
Replacing rusted or damaged corner beads, stop beads and bellcasts that cause staining, cracking and render loss.
Render Survey and Damp Investigation
Tapping, inspection and moisture checks to map failing render and find the cause before any repair starts.
Crack Repair near you
Get a free render repair quote
Tell us what you need and we'll come back with a clear price.
Request a quote