Guide · Homeowners · 3 min read · Updated 17 November 2026
Blown Render: Patch Repair or Full Re-Render?
Short answer
Blown render has lost its bond with the wall and sounds hollow when tapped. Isolated blown areas can be cut back to sound edges and patched at around £60–£120 per m². If a large proportion of a wall is hollow, patches keep failing, or the render is the wrong type for the wall, full re-rendering is usually better value and more reliable over time.
What blown render is
Render is meant to bond firmly to the wall behind it. Over time, water, frost, poor preparation or movement can break that bond, leaving a layer of render that is still in place but no longer attached. This is called blown, hollow or debonded render. It may look fine from a distance, but tapping it with a knuckle or the handle of a screwdriver gives a dull, hollow sound rather than a solid knock.
Blown render eventually cracks, bulges and falls away. Before that, it lets water collect behind it, which can soak the wall and cause damp inside.
How to find blown render
A tapping survey is the standard method. The specialist works across the wall in a grid, tapping with a small hammer and marking hollow areas with chalk. On upper floors this needs safe access. The result is a map showing how much of each elevation has failed, which drives the decision between patching and re-rendering.
Visual signs help too. Look for bulges, cracks with raised edges, staining where water has tracked down, and areas where paint is peeling more than elsewhere. Internal damp patches on outside walls can also point to failed render above or nearby.
- Hollow sound when tapped
- Bulges or raised edges along cracks
- Staining or green growth in patches
- Internal damp on the same wall
- Pieces of render on the ground below
Why render blows
Water is the most common cause. Rain enters through cracks, failed sills, leaking gutters or gaps around windows, soaks into the bond line and freezes in winter, forcing the render away from the wall. Poor original preparation is another: render applied to a dusty, painted or over-smooth surface without a key or bonding agent never bonds properly.
Incompatible materials cause problems too. Hard cement render on soft old brick or lime mortar often fails, because the wall and render move differently and moisture is trapped behind the dense render. Rusting beads, ivy roots and structural movement can also break the bond.
Comparing patch repair and re-rendering
The right choice depends on how much has failed, why it failed and what the wall needs. Patching is the obvious choice when only a few areas are affected and the rest of the render is sound and suitable for the wall. Re-rendering makes sense when failure is widespread, when patches have been tried and keep failing, or when the existing render is the wrong material.
Re-rendering also brings a fresh, uniform finish, whereas patches on old render can be visible, especially on through-coloured systems.
| Situation | Better option |
|---|---|
| A few isolated hollow areas, rest sound | Patch repair |
| Hollow areas spread across most of the wall | Re-render |
| Previous patches failing again | Re-render |
| Cement render on a solid-walled period house | Remove and re-render in lime |
| Colour match important on through-coloured render | Consider re-rendering the elevation |
| Damage caused by a fixable leak | Fix leak, then patch |
How a patch repair is done
The hollow area is marked out and cut back to sound render with a grinder or bolster, usually in a neat rectangle so the edges are straight and strong. Loose material is removed and the wall is cleaned and dampened or primed. The cause of the failure is dealt with, such as replacing a rusted bead or fixing a leaking downpipe.
New render is then built up in the same number of coats as the original, with mesh across the joint between old and new where appropriate. The finish is matched as closely as possible in texture and, for painted render, painted to blend in. Patch repairs typically cost £60–£120 per m², with a minimum charge for small areas.
Lime render and period homes
Blown render on an older, solid-walled house needs extra thought. Many period homes were originally rendered in lime, then patched or re-rendered in cement during the twentieth century. Cement is denser and less breathable than lime, so moisture that would have evaporated through the wall gets trapped behind it. The cement then debonds, and patching with more cement repeats the cycle.
If your house was built before about 1919 and has solid walls, ask the specialist to identify what the existing render is made of. If it is lime, repairs should be in lime with a compatible mix and texture. If it is cement on a wall that should breathe, widespread blowing is often a sign that the render as a whole is unsuitable, and removing it in favour of lime may be the lasting fix. On listed buildings, repairs that change the character of the finish, including replacing lime with cement, may need listed building consent, so check with the local planning authority first.
Costs and getting advice
If more than around a third of a wall is hollow, ask for a re-render price as well, as patching becomes poor value. A render survey with a written report typically costs £150–£350 and is often credited if you go ahead with the repairs. We arrange vetted, insured local render specialists who map the failure and explain both options honestly.
Questions people also ask
Is blown render dangerous?
It can be. Large sections of blown render can eventually fall, which is a risk to people below, especially from upper floors or above doorways. It also lets water into the wall. If render is bulging, cracking or has started to drop, have it checked and made safe promptly.
Can you fix hollow render without removing it?
Generally no. Render that has lost its bond needs cutting back to sound edges and rebuilding. Injecting adhesives behind hollow render is sometimes offered but is rarely a reliable long-term fix for external walls. Patching properly, or re-rendering where failure is widespread, is the standard approach.
How do I know how much render has blown?
A tapping survey maps it. The specialist taps the wall systematically and marks hollow areas, building a picture of how much of each elevation has failed. Upper floors need a tower or scaffold for a full survey. The results show whether patching or re-rendering is the better choice.
Written and checked by the Render Repair team. Read our editorial policy.
More guides
How Much Does Render Repair Cost in the UK? 2026 Guide Prices
Small ground-floor crack repairs start from about £150. Patching blown or hollow render typically costs £60–£120 per m², pebbledash patch repair…
Why Is My Render Cracking? Causes, Types and When to Worry
Render cracks for several reasons: shrinkage as cement render dries, thermal movement, rusting corner beads, water getting behind the render, missing…
Pebbledash Repair or Removal: Options, Costs and What to Expect
Small areas of failed pebbledash can be patched by cutting back to sound render, applying new render and hand-throwing matching aggregate into it,…
How to Clean Render: Removing Algae, Green Stains and Dirt
Green and black staining on render is usually algae, lichen or mould growing on damp, shaded walls. The safe way to clean it is a biocide treatment,…
Get a free render repair quote
Tell us what you need and we'll come back with a clear price.
Request a quote